CONTACT. kingsmill industries pinxton headquarters. UK Head Office. Earth Rods and Accessories. Earth Rods and Accessories. Earth Rods. Copperbond Earth Rods, deep driven, usually provide the most cost effective.
|Published (Last):||18 December 2017|
|PDF File Size:||10.2 Mb|
|ePub File Size:||19.37 Mb|
|Price:||Free* [*Free Regsitration Required]|
The purpose of a lightning protection system is to shield a building, its occupants and contents from these adverse effects. To do this properly the lightning protection system must capture the lightning, lead it safely down to earth, and disperse the energy within the ground. Whether or not a building needs a lightning protection scheme depends on several factors.
Lightning Protection & Earthing – A Brief Guide By Kingsmill Earthing
The code of practice for Protection of Structures against lightning details these and are used to estimate risk. In the resulting calculation, if the risk is found to be less than 1: However, this needs to be assessed in relation to the consequences of a direct strike.
For instance, if the building is an explosive store then the highest level of protection will be required even if the risk of a strike is low.
Elements of a Lightning Protection System. In general materials used for a lightning conductor are high purity copper or aluminium of a similar grade to that used in electrical conductors. The low impedance kingxmill are required to ensure that the lightning energy will flow safely to the ground.
The principal parts are detailed below. Since no part mingsmill the roof should be more than 5m from the nearest horizontal conductor, a 10m x 20m lattice is generally used on large buildings. Traditional taper-pointed air terminals are not as frequently used today but when they are they should be positioned near those points where a strike is most likely to hit the building.
The purpose of the down conductor is to provide the low impedance path from the air termination system to the earth system. There is typically one down conductor for every 20m or part thereof the building perimeter at roof or ground level.
If the building is above 20m in height or of an abnormal risk this distance should be reduced to 10m. Any good conductor which forms part of the building structure can be employed as a down conductor with appropriate connection to the air termination and earthing systems.
For down leads not part of the structure, copper earth tapes and aluminium earth tapes are the most widely used materials. These are sometimes PVC sheathed copper earth tapes for aesthetic eaething only. Where practical they should be routed directly from the air termination to the earth system and be spaced symmetrically around the outside walls of the structure.
At all times consideration must be given to the possibility of side flashing. Each down conductor should also be provided with a test point earthimg a means of isolating the earth electrode for test purposes. The most common terminations are copper earth rods driven into the ground. These should be a minimum of 9 metre for the whole system.
This should be at least 0. The ring conductor is made from copper tape or cable aluminium is not permitted for use below ground and also helps to provide potential equalisation at ground level, in addition to potential earthign.
The earth system should be designed as a whole since the complete installation eartning rise in potential together, to avoid excessive voltage differences.
Lightning Protection & Earthing – A Brief Guide By Kingsmill Earthing
For this reason, the earth termination should be bonded to the rest of the earth electrodes. Finally, it is usual for the lightning protection system and main power earths to be interconnected. However, where this is not desirable for technical reasons, an earth potential equaliser can be installed between them.
The function of this device earthinng to only connect the earths should the voltage between them rise above a certain value. An important element in the design of a lightning protection system is the consideration of bonding of exposed metalwork on or near the structure. This is to ensure that side flashing does not occur.
If exposed metalwork such earthimg pipes or ducts etc. There would therefore be a potential difference between them.
KINGSMILL EARTHING, LIGHTNING PROTECTION, SURGE PROTECTION, EARTH BARS, EARTH RODS EARTH CLAMPS
If this potential difference was greater than the breakdown value of the air or material in between, then a side flash could occur resulting in severe damage.
For external bonds the cross section of the bonding material should not be less than that of the main conductors. Internal bonds can however be of smaller cross section since they are mainly for equipotential purposes and are unlikely to carry a proportion of the lightning current. Kingsmikl various standards for earthing provide design limits to be met and together with codes of practice explain how the earthing system can be designed to meet these.
There are differences in the design limits applying to consumer installations and to supply industry installations and reference should be made to the correct standard to check the limits which apply in each situation.
In the past, it was normal practice to design an kingsjill system to achieve a certain impedance value. The earth electrodes being positioned near the equipment where a fault current was darthing to pass.
Recently, this has changed towards the approach used in North America. The most important difference is that the earthing system is designed to ensure that potentials in its vicinity are below appropriate limits. These potentials are referred to as: A number of factors will determine whether or not a person experiencing any of these potentials will be at risk, and the standards attempt to take these into account to ascertain the limits kkngsmill which the design will be considered acceptable.
Kingsmill Industries UK Ltd are a leading manufacturer and supplier of earthing materials and lightning protection products for the UK and international markets. Kingsmill products are designed, manufactured and tested to meet rigorous standards ensuring high levels of safety and protection for buildings, earthibg, livestock, content and sensitive electronic equipment.
History of Kingsmill Earthing. Kingsmill are proud to be a UK owned, family run business, located in the heart of the UK and are pleased to say that they have been supplying excellent service into the industry for the last 15 years.
Since their inception inKingsmill have gone from strength to strength and have developed into one of the industry market leaders – Kingsmill have done this by focusing on service, quality, price, delivery, commitment exrthing trust. Kingsmill aim to provide the highest standard of Earthing and Lightning Protection Products: Exrthing commitment to quality follows throughout all aspects of the company including manufacture, development, customer support and service.
Kingsmill thrive on solving customer products problems.
In their dedicated workshop, using a combination of high tech machinery and skilled staff Kingsmill Earthing have the ability to engineer or modify product items to your exact requirements.
From a simple modification to eqrthing complete new bespoke item. Kingsmill Earthing have been manufacturing excellence since Go back to blog index. Soil resistivity The external dimensions of the structure including any adjacent structures that are electrically connected The flash density in thunderstorm days per year for kingamill area The type of construction Height above sea level Proximity of other structures such as tall trees The length of any earhing cables entering the structure.
Elements of a Lightning Protection System In general materials used for a lightning conductor are high purity copper or aluminium of a similar grade to that used in electrical conductors. Down Conductors The purpose of the down conductor is to provide the low impedance path from the air termination system to the earth system.
Earthing The various standards for earthing provide design limits to be met and together with codes of practice explain how the earthing system can be designed to meet these. See – Copper Earthing Mats Lattice For Combatting Step Potentials Problems ii Touch Potential the potential difference during fault conditions between exposed metalwork and a point on the soil surface iii Transfer Potential the potential difference between as insulated cable connected to a remote earth reference and the earth rod A number of factors will determine whether or not a person experiencing any of these potentials will be at risk, and the standards attempt to take these into account to ascertain the limits below which the design will be considered acceptable.
Click for more info.