IBANEZ S520EX MANUAL PDF

The SEX is an S series solid body electric guitar model introduced by Ibanez in It was initially produced in Korea and then later in Indonesia. There’s no way a guy who does a couple guitar setups every day of the year would do a better than someone will with instructions from the. For over 18 years, Ibanez RG guitars with Edge double locking sys- tems have been SEX MOF. • 3pc Wizard II Manually Adjustable Zero. Point System.

Author: Mezishicage Daisar
Country: Canada
Language: English (Spanish)
Genre: Career
Published (Last): 6 September 2010
Pages: 353
PDF File Size: 15.82 Mb
ePub File Size: 3.50 Mb
ISBN: 225-8-26326-350-5
Downloads: 43509
Price: Free* [*Free Regsitration Required]
Uploader: Taut

Cut off the ball end of the new string above the string winding and insert s520ez end of the string in between the main saddle and the String holder block 4. If the intonation is still not correct repeat steps 1, 2 and 3. If the 12th fret is flatter than the open note, the saddle needs to be moved forward.

| Wiring Diagrams

The Overall Tremolo height can be adjusted by raising or lowering the Height Adjustment screws 5 on either side s502ex the bridge. If the 12th fret harmonic pitch is lower than the fretted note, the saddle needs to be moved back. To further reduce the torque, remove both bushings. To replace the bushings, remove the bushings by spreading opening the bushing until it is removed. The height adjustment of the tremolo can be set by using the two 4mm adjustment screws 2 on either side of the tremolo unit.

Play the harmonic at the 12th fret, compare it to the fretted note at the 12th fret, these notes should read the same on the tuner. This adjustment should be performed periodically and only by qualified repair personnel.

| Help & How To

The Saddles are preset on the plate. Loosen the string stopper screw 8 by using a 3mm allen wrench remove the string from the saddle. The height adjustment of the tremolo can be set by using the two 3mm adjustment screws on either side of the tremolo unit. To reduce the torque, remove one bushing on the lower side. Loosen the string stopper bolt by using a 3mm allen wrench, and remove the string from the saddle.

  DESCARGAR LIBRO NO FUE LA SUERTE ELIYAHU GOLDRATT PDF

Tremolo Angle Adjustment The tremolo system should sit parallel to the surface of the guitar body, as shown in the illustration. The purpose of this is to accommodate for different tunings or different gauges of strings. Turn the Arm torqueadjustment nut turns counter clockwise.

Wiring Diagrams

Before adjusting the intonation, first determine the direction that the saddle needs to be moved. Loosen the heigth adjustment screw 5 on both sides of the bridge using a 2 Phillips. On the bass plate there are two holes for each saddle lock down screw. TZ Bridges The Overall Tremolo height can be adjusted by raising or lowering the Height Adjustment screws 5 on either side of the bridge.

Loosen the pressure pad screws on the top lock with a 3mm allen wrench and loosen the string to be adjusted. Wind the string around the tuning machine and tune to pitch 6.

If lower than standard settings are desired, this can often result in”buzz” or “rattle” of the strings. Raise or lower the tremolo to the desired string height using a 4mm allen wrench.

Loosen the Saddle lack down ibwnez 9 on the saddle to be adjusted with a 2mm allen wrench.

S520EX (2005–2009)

Remove the tremolo cavity cover plate from the back of the body. To adjust the string height of the saddles use a 1. Play the harmonic at the 12th fret, compare it to the fretted noteat the 12th fret, these notes maunal read the same on the tuner. Insert the tremolo arm into the arm socket and firmly push down until manial arm snaps into place Note: To remove the tremolo arm, firmly hold the arm at the break over point bend and pull up until the arm is released.

Occasionally, there are times when the neck may need adjustment. Products and specifications are subject to change without notice. If the 12th fret is sharper than the open note, the saddle needs to be moved back. Loosen the string by turning the tuner and then remove the string. To allow the arm to swing freely. Adjusting the String Height. Only loosen the screw enough to move the saddle.

  ITEXTSHARP SAVE ASPX AS PDF

Adjusting the intonation is performed by moving the individual string saddles forward or backward. Wind the string around the tuning machine and tune to pitch. Both bushings should be completely hidden. The truss rod is adjustable at the headstock using as allen wrench or an adjustment wrench.

Insert the tremolo arm into the arm socket and turn the Arm torque adjustment nut A clockwise until it stops. After changing the desired strings retune all the strings to the proper pitch and tighter the top lock pressure pad screws.

Cut off the ball end of the new string above the string winding and insert the end of the string in between the main saddle and the string holder block.

Always loosen the Stud lock screws counter clockwise with a 1. To change the strings angle adjust the two 2mm 6 screws on the highside of the bridge, chanding the pivot angle. Insert the tremolo arm into the arm socket and firmly push down until the arm snaps into place.

If the intonation is still not correct repeat steps 2 and 3. Tighten the pressure pad screws. When the guitar is properly adjusted, tighten the top lock pressure pad screws 5. Using a Phillips head screwdriver, turn the spring tension adjustment screw and adjust the length of the spring.

Loosen s502ex heigth adjustment screw 5 on both sides of the bridge using a 2 Phillips 2.